RME User Forum — New HDSP(e) series Windows driver generation 4.x

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (Dandruff) — Sun, 21 Jun 2015 17:18:26 +0000

They already do.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (RME Support) — Sun, 21 Jun 2015 12:40:07 +0000

Windows 10 neither requires new firmware nor specific "driver support".

Regards
Daniel Fuchs
RME

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (Thermaltake) — Sun, 21 Jun 2015 06:51:31 +0000

Question Windows 10 is around the conrner is it going to be firmware update like XP to 7 or just normal support for Windows 10 will be added ?

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (MC) — Fri, 29 May 2015 02:43:11 +0000

The Settings dialog does not have a Taskbar icon.

The level meter communication is started and causes this on all RME devices, so fully normal too.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (TabSel) — Mon, 25 May 2015 07:54:59 +0000

Concerning the last questions, I may help, as I think I see the same with my system (HDSP Digiface PCI):

I boot the PC, then open TotalMixFx. I see the SPDIF out meter showing a level, even though nothing gets out SPDIF. The Meter then goes down to zero.

So, the initial metering value doesn't seem to come from hardware. Subsequent metering levels do come from hardware, so the meter goes down to zero...

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (MC) — Mon, 25 May 2015 01:19:43 +0000

Did you check that the TM FX icon is not just hidden behind the small triangle? And the second question I simply don't understand.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (undertone) — Mon, 15 Dec 2014 16:22:57 +0000

I'm just updating this thread with what has become routine using v4 with an HDSPe ExpressCard and a Multiface 1 on a MBP: as I've gone back to using the "Disconnect" I/O Box function in the settings before putting the MBP to sleep because otherwise there still is an audio transient created on wakeup (seems lower in level than with the older drivers). But on wakeup, the Settings have to be closed and relaunched for then to see the HDSPe device. After that I can uncheck "Disconnect" and all is well.

However, if I wake up the MBP and don't touch the Settings at all (no card recognized/indeterminate state), inevitably after a time TMFX will start using massive amounts of CPU for no clear reason. At that point I just Quit both apps and relaunch Settings and then TMFX and everything is normal again. FYI.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (HollowMac) — Mon, 15 Dec 2014 10:27:08 +0000

RME Support wrote:

Please install TMFX 1.05: http://www.rme-audio.de/forum/viewtopic.php?id=21006

I confirm (about loopback feature on ADAT 7/8): I tried this week-end and it works! Thanks a lot.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (lunatic) — Sun, 14 Dec 2014 15:45:20 +0000

I do get occasional (happened two times) BSOD with the new software (nothing else on the system changed) this is causing TM FX to forget all settings including layouts and channel names. Any ideas why and how to restore the settings easily?

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (RME Support) — Mon, 08 Dec 2014 15:59:25 +0000

Please install TMFX 1.05: http://www.rme-audio.de/forum/viewtopic.php?id=21006

Regards
Daniel Fuchs
RME

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (HollowMac) — Mon, 08 Dec 2014 15:44:39 +0000

Hi,

I have a Multiface II and I am using the latest versions of TotalMix FX and Windows drivers ; also, the firmware of my HDSPe card is up to date.

I encounter the following problem: there is no loopback functionality for ADAT outputs 7/8 (loopback is available for ADAT outputs 1 to 6).

Is this a bug or an hardware limitation? I don't remember if the loopback was available for these outputs on old versions of TotalMix.

Best Regards.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (juanlibertella) — Mon, 08 Dec 2014 15:39:25 +0000

juanlibertella wrote:

In the last days TotalMix Fx freeze randomly and I have to restart the PC, the screen show the meters and the faders always in the same position and incontrollable with mouse or with BCF2000.

The problem was the Behringer BCF2000 when disconnecting regain control of TotalMix FX

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (ms) — Wed, 26 Nov 2014 09:01:15 +0000

I see. Thank you for clearing that up.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (MC) — Wed, 26 Nov 2014 08:47:30 +0000

That is version 2.01. All new features in there. TM FX is version 1.03 and can be updated with 1.05 from the TM FX forum.

Re: New HDSP(e) series Windows driver generation 4.x

null@example.com (ms) — Wed, 26 Nov 2014 08:32:44 +0000

The version 4 driver for MADI FX and MADIface XT in PCIe mode has not yet been released, right?