Clipping/overload indicator in the matrix view.

Can you make the cells go red when it clips?

Thanks.

Feature request for TM Remote:
Can we get access to import for Room EQ also via remote. Would make it so much easier for me.

Not a problem today, but nice to have.

Best,
Pål S

I tried all of that, and definitely killed all relevant processes prior to copying over the file. Again, About shows I'm on 1.97, the file in System32 is the 1.97 version and my firmware is current on my UFXIII. I even reinstalled the drivers and downgraded to 1.96 (Room EQ still not there) and then upgraded to 1.97 per the instructions, but Room EQ is still not showing up. Is there another way to confirm which version is running?

Again, see here, that in the System32 file I have 1.97:

Room EQ is on the wrench tab of the output, not on the EQ tab. Did you look there? Otherwise no need to juggle with executables and DLLs.

This makes no sense.

Would you please add more shortcut options in the "Arc & Key" command section of TotalMix in order to assist Blind/Visually Impaired persons to access more settings in their RME product?

Thanks all over the place.

I wrote in the 1.96 Beta thread reporting a small issue regarding fader groups not being saved under certain conditions and I've just discovered now in 1.97 b1 a bit more about the issue.

I'm trying to save 2 different output faders into a Fader group - one stereo main out and one mono LFE output. Use case here is trying to sync a subwoofer fader to be part of main volume out in a 2.1 setup.

I have a workspace where one snapshot is 2.0 and another snapshot is 2.1. If I save the workspace when the 2.1 snapshot is selected and fader group on as described, and later reload this workspace, the Fader group with Main Out + LFE out is still grouped as expected. If I then select any other snapshot and come back to my 2.1 snapshot the LFE channel is not remembered in the group I made.

Also if I save the workspace with anything other than the 2.1 snapshot selected and reload the workspace and then select the 2.1 snapshot the LFE fader is also left out of the group.

Hopefully this makes sense so it can be logged.

I wanted to add one more comment about my earlier post in this thread about 2.1 bass management and the groups issue I mentioned.

My workaround for this is to have a whole workspace dedicated to only 1 snapshot that has the bass management set up with the fader group on. If I do this and only have one snapshot in the workspace the grouping works. It's only when you open a workspace and switch to a different snapshot that the grouping issue arises.

Kind regards

I was able to quit Totalmix, restore my 12mic saved preset via web interface, restart Totalmix and all my settings came over.

Thanks!

I am just wondering if the selected Layout Preset is not being recovered after restarting TM FX either
a) by quitting TM FX and restarting or
b) by rebooting the PC.

If you select a Layout Preset the button turns blue and stays blue when loading a workspace or workspace quick select slot.

But as soon as you quit TM FX and restart it, then all Layout Preset buttons are dark.

Shouldn't it be the case, that TM FX should represent the last state when starting up?
And to the last state I would also regard the selected Layout Preset and then it should be lit.

Layout Preset selected and stored to Snapshot1:

After Restart of TM FX:

I like the new features to remember the last configured Bank under "Settings -> Aux. Devices" and showing the status of a remote connection, whether its "active".

This is very user-friendly and gives a good overview on whether remote control is established.

Also thanks for implementing knobs for TRS and Inst on 12Mic's channels 1-4, works like a charm :-)

1) Or does the "Always init DSP devices with Total Mix FX setting" get saved within a workspace anyhow?
2) The do not load "--" as default after install I find really important though, in order to correctly transfer workspaces.

Preferences are stored separate from workspaces.

You find the XML file on Windows in the user profile, location:

C:\Users\<username>\AppData\Local\TotalMixFX\rme.totalmix.preferences.xml

The mentioned settings are in the XML element "Preferences"

<Preferences>
        <Preferences>
                         [...]
            <val e="DoNotLoadMainVolume" v="0"/>
                         [...]
            <val e="AlwaysUseTotalmixSettings" v="1"/>
                         [...]
        </Preferences>
[...]
</Preferences>
[...]

The preferences should not change that much, for me its always the same so you can configure it one time and then forget about it.

As the file also contains the names of Quick Workspace Select files, I would recommend making the required changes one time in TotalMix FX.

Or to change the default to what most people would regard as useful (the topic of your request, in the hope that it also serves others well).