Hallo RunWithOne,
Ich habe das selbe Problem mit meinem neu gekauften Astell&Kern SE200 an meinem RME Adi 2 Pro FS.
Obwohl der SE200 768 KHz schafft. Habe bisher jedoch keinen File mit 768 MHz probiert.
Beide Geräte erkennen den USB Betrieb.
Anzeige : USB conn SR 768 State 2/2
Jedoch kein Ton.
Kabel getauscht ... Hat alles nichts gebracht.
Mit den DAPs Ibasso DX200, Fiio M15 und sogar den Astell&Kern SR25 hat es einwandfrei funktioniert.
Konntest du das Problem beim SE100 lösen?
Würde mich freuen, wenn es eine Lösung gab. Würde den SR200 gerne behalten, jedoch wenn ich nicht streamen kann macht der sE200 keinen Sinn für mich, auch wenn die Kopfhörer Audioqualit super ist.
Klingt seltsam aber ich verwende momentan ein altes Samsung Note 4 ( Version SM-N910C , mit Exynos Chip und dedizierten Wolfson Dac, Nicht mit Snapdragon. Ich hatte mich deshalb für diese Version entschieden. Die Version gab es nicht in Deutschland, habe sie in Tschechien bestellt). Es ist einfach ein Traum was für eine Klanqualität aus meiner 2.1 Kette
Samsung Note 4 - RME - Dynavox VR20 Röhrenverstärker - B&W 706 S2 + Arendal aktiv Sub 1961 1S
rauskommt. Einfach nur fantastisch.
Leider kommt der Note 4 so langsam ins Ruckeln, weil er schon alt ist und unter Android 6 läuft.
Ich schaue mich daher nach einem neuen Abspielgerät um. Die USB Qualität des Note 4 ist derartig super, dass alle oben genannten und getesteten DAPs in meiner HiFi Kette nicht mithalten können, was den ausgewogenen Klang , die Räumliche Tiefe und Breite und plastische Projektion anbelangt. Der Note 4 scheint alles immer auf 192 KHz hochzuskalieren.
Deshalb habe ich den SE200 bestellt in der Hoffnung, dass der im USB Audio Betrieb so gut ist wie der Note 4.
Aber leider funktioniert der überhaupt nicht.
Viele Grüße
Englisch Version
Hello RunWithOne,
I have the same problem with my newly purchased Astell & Kern SE200 on my RME Adi 2 Pro FS. Although the SE200 manages 768 KHz. So far, I haven't tried a file with 768 MHz. Both devices recognize USB operation. Display: USB connSR 768 State 2/2 However no sound. Cable exchanged ... Nothing worked.
With the DAPs Ibasso DX200, Fiio M15 and even the Astell & Kern SR25, it worked perfectly.
Could you solve the problem with the SE100?
I would be happy if there was a solution. Would like to keep the SR200, but if I can't connect the SE200, je makes no sense for me, even if the headphones audio quality is great.
Sounds strange but I'm currently using a very old Samsung Note 4 (version SM-N910C, with Exynos chip and dedicated Wolfson Dac, not with Snapdragon. That's why I choose this version. The version was not available in Germany, I ordered it in the Czech Republic).
It is just a dream what sound quality from my 2.1 chain
Samsung Note 4 - RME - Dynavox VR20 tube amplifier - B&W 706 S2 + Arendal aktiv Sub 1961 1S comes out. Just fantastic.
Unfortunately, the Note 4 starts to stutter because it is already old and runs under Android 6.
So I'm looking around for a new player. The USB quality of the Note 4 is so great that all of the above mentioned and tested DAPs in my hi-fi chain cannot keep up in terms of balanced sound, room dept, width and plastic projection. The Note 4 always seems to upscale everything to 192 KHz.
That's why I ordered the SE200 in the hope that it would be as good as the Note 4 in USB audio mode. But unfortunately it doesn't work at all.
Best regards