• guss
  • ADAT user
  • Offline
  • Registered: 2012-04-25
  • Posts: 29

Topic: Driver doesnt load or do anything

Windows 10 64 bit ,  hdspe Raydat

My driver would load automatically but clicking on total mixx wouldnt do anything. It was working yesterday - today nothing . So I uninstalled everything and reinstalled the new drivers. Nothing - the driver doesnt even load automatically anymor eand clicking totalmix does nothing. Any help ?
These are the drivers I installed :

https://www.rme-audio.de/en/downloads/driver/hdspe.php

and this version of totalmix :

https://archiv.rme-audio.de/download/totalm … n_1503.zip

  • From: Germany
  • Registered: 2007-04-10
  • Posts: 9,843

Re: Driver doesnt load or do anything

Hello,

what does "load automatically" refer to? Which driver exactly did you install and how so?

Regards
Daniel Fuchs
RME

Regards
Daniel Fuchs
RME

RME Support's Website

3 Reply by guss (edited by guss 2019-06-07 12:58:40)

  • guss
  • ADAT user
  • Offline
  • Registered: 2012-04-25
  • Posts: 29

Re: Driver doesnt load or do anything

RME Support wrote:

Hello,

what does "load automatically" refer to? Which driver exactly did you install and how so?

Regards
Daniel Fuchs
RME

Normally when I start windows the driver and totalmix icons are in the systray in the bottom right hand corner of windows. Also the driver shows up  in any audio software under drivers. It does not do that at the moment.

  • vinark
  • DAW Mastermind
  • Online
  • Registered: 2009-06-05
  • Posts: 2,859

Re: Driver doesnt load or do anything

This means the card is not seen by windows (or mac?) Look in device manager. If it is not there, reseat the card, try a different slot or clean the pcie contact with an eraser gum.

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632

5 Reply by guss (edited by guss 2019-06-07 13:00:20)

  • guss
  • ADAT user
  • Offline
  • Registered: 2012-04-25
  • Posts: 29

Re: Driver doesnt load or do anything

vinark wrote:

This means the card is not seen by windows (or mac?) Look in device manager. If it is not there, reseat the card, try a different slot or clean the pcie contact with an eraser gum.

Ok will do - what section should it be listed under in device manager ?

6 Reply by vinark (edited by vinark 2019-06-07 13:08:32)

  • vinark
  • DAW Mastermind
  • Online
  • Registered: 2009-06-05
  • Posts: 2,859

Re: Driver doesnt load or do anything

audio devices.
If it is malfunctioning, which is also possible, there could be a yellow unknown device somewhere.

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632
  • guss
  • ADAT user
  • Offline
  • Registered: 2012-04-25
  • Posts: 29

Re: Driver doesnt load or do anything

I got it working - I needed to change hdspe slot for some reason . Thanks for your prompt support as always .

  • vinark
  • DAW Mastermind
  • Online
  • Registered: 2009-06-05
  • Posts: 2,859

Re: Driver doesnt load or do anything

Cheers, always nice to help a fellow user (of RME that is).

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632
  • tzzsmk
  • tzzsmk
  • AES/EBU artist
  • Offline
  • Registered: 2016-03-14
  • Posts: 139

Re: Driver doesnt load or do anything

guss wrote:

I got it working - I needed to change hdspe slot for some reason . Thanks for your prompt support as always .

certain motherboards also have some sort of "Early PCIe Delay" setting in BIOS,
which basically means if a PCIe device does not draw enough power at boot (such as RME HDSPe cards), it disables entire PCIe slot before operating system starts booting (!)

HDSPe AIO, ADI-2 DAC, Fireface UFX, Octamic D, Octamic II
Reaper, Windows 11, M2 Studio