• Registered: 2017-02-04
  • Posts: 12

Topic: Visualize MAIN as separated-individual mono channels.

Hello,

I'm working with a FF 802

Concerning the "Hardware outputs " section, is it possible to visualize  channels 1 and 2 not as part of  the "Main" channel but as two individual-separated mono channels (Analogue 1 and 2?) at the left of AN 3?

Can I get rid of the "Control Room" section and visualize the channels in it  as mono- individual channels?

I would like to visualize  the channels Analogue out 1 and 2 as mono channels , each one with its own different meter (just like analogue 3, 4, 5... etc.). It seems like the "Stereo" button of the "Main" channel is blocked, so, I can not split it .  I don't find any answer in the user manual or the video tutorials.

I'd appreciate any support here, thanks.

2 Reply by MC

  • MC
  • MC
  • Administrator
  • Offline
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,599

Re: Visualize MAIN as separated-individual mono channels.

You either Assign Mains to None or to any channels you don't need.

Regards
Matthias Carstens
RME

MC's Website

  • Registered: 2017-01-20
  • Posts: 22

Re: Visualize MAIN as separated-individual mono channels.

Hey Matthias,
I wondered about this the other day and couldn't find the option when right clicking on 'MAINS' to select 'NONE'?

  • vinark
  • DAW Mastermind
  • Offline
  • Registered: 2009-06-05
  • Posts: 2,779

Re: Visualize MAIN as separated-individual mono channels.

althemusicwizard wrote:

Hey Matthias,
I wondered about this the other day and couldn't find the option when right clicking on 'MAINS' to select 'NONE'?

A little to the right  at the side control room, under assign

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632
  • Registered: 2017-01-20
  • Posts: 22

Re: Visualize MAIN as separated-individual mono channels.

Thanks for those replies. If you watch the next video you'll see I have not got the option:

https://www.youtube.com/watch?v=Un_JlZZ … e=youtu.be

Al

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,210

Re: Visualize MAIN as separated-individual mono channels.

althemusicwizard wrote:

Thanks for those replies. If you watch the next video you'll see I have not got the option:

https://www.youtube.com/watch?v=Un_JlZZ … e=youtu.be

Al

What RME interface do you have and which driver / totalmix version do you use ?

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14
  • vinark
  • DAW Mastermind
  • Offline
  • Registered: 2009-06-05
  • Posts: 2,779

Re: Visualize MAIN as separated-individual mono channels.

I have HDSP version 1.12 and have none for main out.....

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632

8 Reply by althemusicwizard (edited by althemusicwizard 2017-02-09 16:07:05)

  • Registered: 2017-01-20
  • Posts: 22

Re: Visualize MAIN as separated-individual mono channels.

I have a Fireface UFX, DSP-SW Version 1.63

Total Mix FX Version 1.40

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,210

Re: Visualize MAIN as separated-individual mono channels.

I have the UFX+, but also TM FX 1.40.

Could you try to save your TM settings and then perform a complete reset of TM FX (Reset Mix -> Total Reset) ?

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14
  • Registered: 2017-01-20
  • Posts: 22

Re: Visualize MAIN as separated-individual mono channels.

I regularly save my workspace as I treat the unit like a digital mixer (saving both snapshots and workspaces).

After re-setting the mixer the situation is the same.....there is no option under MAINS for 'None'.

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,210

Re: Visualize MAIN as separated-individual mono channels.

Sorry no further ideas.

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14

12 Reply by MC

  • MC
  • MC
  • Administrator
  • Offline
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,599

Re: Visualize MAIN as separated-individual mono channels.

Not all units support 'None'. That's why I wrote 'or to any channels you don't need.'

Regards
Matthias Carstens
RME

MC's Website