• Armin
  • ADAT user
  • Offline
  • Registered: 2021-04-23
  • Posts: 10

Topic: How to get an initial workspace within TotalMix FX?

Hey there.

I am barely new in the RME world.

I've done quite a few changes and saved it to my workspace. Every time I start TotalMix, this workspace is loaded.

Now, I want to start to reconfigure my whole setup. For this I am looking for a way to get a blank, initial workspace (with blank snapshots and so on).

How can I do this?
I've found the "Options > Reset Mix", but in this case, the Snapshots aren't cleared.


Thank you in advance for your help!

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,201

Re: How to get an initial workspace within TotalMix FX?

There is the possibility to perform a total reset followed by e.g.
- Straight playback with all to Main Out (mapping of "Main Out" to a HW output stays)
- set inputs mono / outputs stereo (ADM)

Sadly the channel width and opened tool submenues can not be reset as well.
This would be very practical.

Sorry, I can give no recommendation which config files to remove to issue a full reset, but without loosing maybe still useful settings (like e.g. EQ settings, TM FX preferences).

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14

3 Reply by MC

  • MC
  • MC
  • Administrator
  • Online
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,599

Re: How to get an initial workspace within TotalMix FX?

See manual, delete the file devicenamelast.xml file.

Regards
Matthias Carstens
RME

MC's Website

4 Reply by ramses (edited by ramses 2022-04-04 05:55:40)

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,201

Re: How to get an initial workspace within TotalMix FX?

MC wrote:

See manual, delete the file devicenamelast.xml file.

I couldn't find this information in manual, I checked several (UFX+, UCX II, BBF Pro FS, UC) by searching for "last.xml".
Also not in the TM FX online help. Maybe this information got lost?

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14

5 Reply by MC

  • MC
  • MC
  • Administrator
  • Online
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,599

Re: How to get an initial workspace within TotalMix FX?

UFX+ chapter 25.7.1. Same for all other interfaces, with respective names.

Regards
Matthias Carstens
RME

MC's Website

  • ramses
  • DAW Mastermind
  • Offline
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,201

Re: How to get an initial workspace within TotalMix FX?

MC wrote:

UFX+ chapter 25.7.1. Same for all other interfaces, with respective names.

Many thanks, Matthias, so the filename was a little bit different, therefore I didn't find it.

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14
  • Armin
  • ADAT user
  • Offline
  • Registered: 2021-04-23
  • Posts: 10

Re: How to get an initial workspace within TotalMix FX?

Thank you! That solved my problem.