301 Reply by KaiS (edited by KaiS 2022-12-13 11:36:52)

  • KaiS
  • DAW Mastermind
  • Offline
  • From: Germany
  • Registered: 2020-02-05
  • Posts: 3,525

Re: ADI-2/4 Prototyp

Babaluma wrote:

I'd like to match it exactly to 21dBu if possible, but am finding the L/R Trim Gain settings a little confusing. Should I:

A) Set it to 19dBu and both the Trim Gains to +2.0dB to achieve 21dBu
B) Set it to 24dBu and both the Trim Gains to +3.0dB to achieve 21dBu

Use B), Ref Level:+24 dB and Trim Gain Left / Right: +3 dB.

Trim Gain range is 0 to +6 dB additional gain, no negative range, so A) wouldn’t work.

A negative trim in the digital domain wouldn’t be recommended anyway, you could never reach 0 dBFS / fullscale and would lose all warning lights that the AD is already overdriven.


According Ref Levels:
• On the inputs, higher value means LESS analog Gain before the AD converter, you need more level to fully drive the AD.

• On the outputs it’s just the other way round, higher Ref Level means MORE analog gain after the DA converter, louder.

KaiS's Website

  • From: Milan, Italy
  • Registered: 2012-02-19
  • Posts: 213

Re: ADI-2/4 Prototyp

Thanks so much for the quick response. Yes I really wasn't sure about positive vs negative values and how they relate etc. I'll go with B!

I just plugged the turntable in too, just stunning! Not had it set up in about three years, blasting The Cramps right now, big smiles! smile

https://musicwall.app/hermetech

Babaluma's Website

  • Registered: 2022-12-03
  • Posts: 6

Re: ADI-2/4 Prototyp

I apologize for the stupid question: I connected two headphones yesterday, one headphone as 4.4mm balanced and one as 6.3mm. The sound on the connection 6.3mm was very strange and I thought the connection would change automatically. 4.4mm was already connected and I wanted to listen only at 6.3mm. For this 3 questions:

1. Is it possible to possibly disable 4.4mm if I want to connect and listen to 6.3mm at the same time?
2. Is the reverse possible?
3. Can any damage have occurred to the headphones at the connection 6.3mm, since the sound has just been so strange?

304 Reply by MC

  • MC
  • MC
  • Administrator
  • Offline
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,586

Re: ADI-2/4 Prototyp

1. No, and that is clearly mentioned in the manual.
2. No again.
3. No once more.

Ph3/4 and PH1/2 give out one channel's sound as phase inverted mono signal. That is the expected signal for balanced mode and connection, but your headphone is unbalanced.

Regards
Matthias Carstens
RME

MC's Website

305 Reply by jusu

  • jusu
  • ADAT user
  • Offline
  • Registered: 2023-02-11
  • Posts: 15

Re: ADI-2/4 Prototyp

hasan.ay386 wrote:

- FIR Linear phase EQ for speaker room correction. (Preferably with 65536 taps, if possible, because many high quality room correction software uses this tap size as a standard and it works well).

With 64k TAPs coefficients for the lowest filter frequency reach down to below 3Hz already regarding lamba when using 192kHz. I even operate with a 64k-TAP-FIR when treating 768kHz signals at least when it comes to low pass.

306 Reply by KaiS (edited by KaiS 2023-02-12 00:55:07)

  • KaiS
  • DAW Mastermind
  • Offline
  • From: Germany
  • Registered: 2020-02-05
  • Posts: 3,525

Re: ADI-2/4 Prototyp

jusu wrote:
hasan.ay386 wrote:

- FIR Linear phase EQ for speaker room correction. (Preferably with 65536 taps, if possible, because many high quality room correction software uses this tap size as a standard and it works well).

With 64k TAPs coefficients for the lowest filter frequency reach down to below 3Hz already regarding lamba when using 192kHz. I even operate with a 64k-TAP-FIR when treating 768kHz signals at least when it comes to low pass.

You both mix FFT and FIR filters.

A 64k Point FFT has a resolution on 3 Hz at a sample rate of 192 kHz, so it’s lowest band covers 0–3Hz.

FIR filters are a different topology that can be linear phase or minimum phase, depending on the filter coefficients.
The number of taps in an FIR-Filter topology does not need to be high, usually just a few, not in the k-taps range.

https://dspguru.com/dsp/faqs/fir/properties/


Practically I do not like FFT based filters for audio very much.
The windowing necessary for the FFT-process produces artifacts, specially at lower frequencies.
FFT is well suited just for measurements, as it has a good band separation.


I even don’t like linear phase filters sound-wise for their impulse response.
Natural filters are all minimum phase (no pre-ringing) as one cannot see into the future - that’s what linear phase filter’s pre-ringing in fact is.

In reality you cannot hear a signal before the drumstick hits the drum.
But linear phase filters produce a signal before, that makes low drums sound like having a fade-in.

ADI-2 offers a FIR based, minimum phase filter EQ, that doesn’t have this problem.

KaiS's Website