• Registered: 2022-01-06
  • Posts: 62

Topic: reinitialiser

Bonjour
Savez vous comment reinitialiser le rme adi2 dac fs

LINN AKURATE DS, LINN UNIDISC SC,AMPLIS MCINTOSH C300 et MC7106 + RME
  • ramses
  • DAW Mastermind
  • Online
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,186

Re: reinitialiser

Manual ch 7 "Returning to Factory State"

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14
  • Registered: 2022-01-06
  • Posts: 62

Re: reinitialiser

Thanks I managed to reset but it didn't solve my problem
for some time (with or without AutoRevel), I have the sound that becomes bad I am forced to lower the volume (I go from 20db to 30 db on the RME) and the left and right baregraphs at the bottom of the screen show that I am at 0 (max permanently)
I am looking for the cause because before the sound was perfect

LINN AKURATE DS, LINN UNIDISC SC,AMPLIS MCINTOSH C300 et MC7106 + RME
  • Registered: 2022-01-06
  • Posts: 62

Re: reinitialiser

The same title from my PC's HDD connected to the RME via the USB input works normally
My problem comes from the COAX link?

LINN AKURATE DS, LINN UNIDISC SC,AMPLIS MCINTOSH C300 et MC7106 + RME
  • From: Germany
  • Registered: 2007-04-10
  • Posts: 9,774

Re: reinitialiser

What's the signal source? Is the ADI set to sync to SPDIF?

Regards
Daniel Fuchs
RME

RME Support's Website

  • Registered: 2022-01-06
  • Posts: 62

Re: reinitialiser

Digital output from my LINN AKRATE DS streamer

LINN AKURATE DS, LINN UNIDISC SC,AMPLIS MCINTOSH C300 et MC7106 + RME

7 Reply by MC

  • MC
  • MC
  • Administrator
  • Offline
  • From: Germany/Thailand
  • Registered: 2007-04-06
  • Posts: 25,586

Re: reinitialiser

When the sound is bad check the ADI's Status Overview display for errors on receiving the SPDIF signal.

Regards
Matthias Carstens
RME

MC's Website

  • Registered: 2022-01-06
  • Posts: 62

Re: reinitialiser

It seems that the problem comes from the streamer

LINN AKURATE DS, LINN UNIDISC SC,AMPLIS MCINTOSH C300 et MC7106 + RME

9 Reply by KaiS (edited by KaiS 2023-02-01 19:03:58)

  • KaiS
  • DAW Mastermind
  • Offline
  • From: Germany
  • Registered: 2020-02-05
  • Posts: 3,525

Re: reinitialiser

ericcholley63 wrote:

It seems that the problem comes from the streamer

Replace the USB cable, nothing fancy needed, but no lomger than 2-3m.

KaiS's Website

10 Reply by john34 (edited by john34 2023-02-08 10:25:39)

  • Registered: 2018-09-03
  • Posts: 52

Re: reinitialiser

As I understand the OP has connected the streamer via coax spdif.
I would check if the digital volume on the linn is below 100%.
He could also check if the testfiles for different sample rates pass.