• G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Topic: hdsp 9632 -not able to use latency under 512 for vsti

Hi!

Suddenly I'm not able to use my Hdsp 9632 under 512 samples when monitoring vsti's.
512 is fine, under gives more and more distortion.
I haven't really checked if audio-monitoring is affected the same way.

Drivers should be newest.
DAW is Reaper
OS: XP sp3

Thanks for all help!

www.g-sun.no/en/

G-Sun's Website

  • Registered: 2011-03-02
  • Posts: 3

Re: hdsp 9632 -not able to use latency under 512 for vsti

i have problems with 1024 samples, playback with 512 is'nt possible in great Arrangements, my drivers are the newest from August 2010

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Seems like playback is affected the same way. I can play a loop with 256, under that, it's just distortion.
Before I had no problem running 64 samples.

www.g-sun.no/en/

G-Sun's Website

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Same in Sonar 8

www.g-sun.no/en/

G-Sun's Website

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Reflashed the card, and everything back to normal smile

Seems however that there are some strange things going on her, since I had driver-problems a couple of weeks ago:
http://www.rme-audio.de/forum/viewtopic.php?id=10343
Any ideas?

www.g-sun.no/en/

G-Sun's Website

  • vinark
  • DAW Mastermind
  • Offline
  • Registered: 2009-06-05
  • Posts: 2,869

Re: hdsp 9632 -not able to use latency under 512 for vsti

Did you do a complete shutdown/cold boot, when these issues happen? If not try that. If you did, try memtest to see if your system is ok

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632

7 Reply by G-Sun (edited by G-Sun 2011-03-04 13:36:49)

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

No shutdown/cold boot when issue appeared. But, did cold boot after reflashing card, so could be that roll
Yes, I'll run a memtest. Thanks!

BTW: Does the firmware load into RAM?

www.g-sun.no/en/

G-Sun's Website

8 Reply by vinark (edited by vinark 2011-03-04 15:22:09)

  • vinark
  • DAW Mastermind
  • Offline
  • Registered: 2009-06-05
  • Posts: 2,869

Re: hdsp 9632 -not able to use latency under 512 for vsti

No onto the card. But indeed could have been just the cold boot that fixed it. I have had that sometimes too, when the lower buffer settings would corrupt (by me by overloading the cpu) and only a reboot would fix it.

Vincent, Amsterdam
https://soundcloud.com/thesecretworld
BFpro fs, 2X HDSP9652 ADI-8AE, 2X HDSP9632
  • v24s
  • ADAT user
  • Offline
  • Registered: 2011-03-04
  • Posts: 9

Re: hdsp 9632 -not able to use latency under 512 for vsti

maby we should go over your system

make and model of whats inside will help..

10 Reply by G-Sun (edited by G-Sun 2011-03-04 23:09:35)

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Thanks smile
My gearlist is:
    * Mainboard : AOpen AX4PER-GN
    * Chipset : Intel i845PE
    * Processor : Intel Pentium 4 @ 3066 MHz
    * Physical Memory : 1024 MB (1 x 1024 DDR-SDRAM )
    * Video Card : RADEON 7000 / RADEON VE Family (Microsoft Corporation)
    * Hard Disk : SAMSUNG (250 GB)
    * Hard Disk : WDC (160 GB)
    * DVD-Rom Drive : TSSTcorp CDDVDW SH-S222A
    * Operating System : Microsoft Windows XP Professional 5.01.2600 Service Pack 3
    * DirectX : Version 9.0c (mars 2006)

www.g-sun.no/en/

G-Sun's Website

  • v24s
  • ADAT user
  • Offline
  • Registered: 2011-03-04
  • Posts: 9

Re: hdsp 9632 -not able to use latency under 512 for vsti

G-sun: what bios rev is the board running and where did you get the chipset/inf
drivers for xp32 for your chipset..

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Thanks!

OEM Signature :    AX4PER-GN R1.05 Jun.23.2004 AOpen Inc.  (Newest)
BIOS Version/Date    Phoenix/Award Technologies, LTD 6.00 PG, 23.06.2004
SMBIOS Version    2.3

The chipset-drivers are updated from AOpen.
But I'm not sure everything is fully updated, cause I found it a little difficult.

www.g-sun.no/en/

G-Sun's Website

13 Reply by v24s (edited by v24s 2011-03-05 20:12:18)

  • v24s
  • ADAT user
  • Offline
  • Registered: 2011-03-04
  • Posts: 9

Re: hdsp 9632 -not able to use latency under 512 for vsti

hello...   AX4PER-GN
BIOS         R2.04     1/27/2005  is the last bios, i did not see updated chipset drivers at aopen for the os, im going to look at intel again, might the issue be your
processor power. Im running X-1a with no errors and it takes a well setup system
with all the processor power you can toss at it, il look back later

this inf is too old

AX4PER-GN
Driver     Intel Chipset Software Installation Driver     R5.00.1012 PV     4/9/2003    
2464.0 KB
#     Intel Chipset Software Installation Utility for Windows 98SE/ME/2000/XP


OS Support:Win2000,Win95,Win98,Win98SE,WinME,WinXP

http://www.intel.com/support/chipsets/sb/cs-009236.htm

Intel® Chipset Software Installation Utility ONLY for 845pe, your board
Intel® 845PE Chipset     **     Download, just this driver

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Thanks a lot smile

The Bios is latest. I have:
Product :    AX4PER-GN
Version :    918AF10401
and the R1.05 is latest for that version.

I'll check up and update the others as you suggested smile

www.g-sun.no/en/

G-Sun's Website

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Checked
http://www.intel.com/support/chipsets/sb/cs-009236.htm
A little unsure about what to download and install, so used the Intel Driver Update Utility:
http://www.intel.com/support/detect.htm
and it reported:
Intel Chipset Software Installation Utility (Chipset INF)    
Product Detected     Intel® 800 Series Chipsets
Current Version Installed     5.00.1012
This version is valid.

I updated just the network-driver, as it was the only thing suggested by the utility.

www.g-sun.no/en/

G-Sun's Website

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Searched for 845PE in the Download Center
but didn't find any thing.
A little unsure about what to do..

www.g-sun.no/en/

G-Sun's Website

  • Registered: 2007-05-09
  • Posts: 649

Re: hdsp 9632 -not able to use latency under 512 for vsti

Latest Intel Chipset Software Installation Utility is version 9.2.0.1021.

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Downloaded:
File name:
INF_allOS_9.2.0.1021_PV.exe   
Version:
9.2.0.1021

In the extraction-part I got the message:
"Your PC does not meet the minimum requirements for installing the software. Setup will exit."

www.g-sun.no/en/

G-Sun's Website

  • v24s
  • ADAT user
  • Offline
  • Registered: 2011-03-04
  • Posts: 9

Re: hdsp 9632 -not able to use latency under 512 for vsti

Dandruff: thanks for the input !! g-sun i was hoping to get you system updated and performing the best it could be............... its going to be hard as intel is not supporting
many of their chipsets and yours is  tough build, many issues with that chipset.

in the futrue if other members would conside this motherboard to build on..

http://www.supermicro.com/products/moth … /C7P67.cfm

you have to wait intel sata issues, but will soon be out.. killer motheboard

  • Registered: 2007-05-09
  • Posts: 649

Re: hdsp 9632 -not able to use latency under 512 for vsti

G-Sun wrote:

Downloaded:
File name:
INF_allOS_9.2.0.1021_PV.exe   
Version:
9.2.0.1021

In the extraction-part I got the message:
"Your PC does not meet the minimum requirements for installing the software. Setup will exit."

Weird. Should install fine on

  Microsoft Windows Server 2003
    Microsoft Windows Server 2003 x64 Edition
    Microsoft Windows Server 2008
    Microsoft Windows Server 2008 x64
    Microsoft Windows XP
    Microsoft Windows XP Professional x64 
    Microsoft Windows 2000
    Microsoft Windows Vista
    Microsoft Windows Vista x64 
    Microsoft Windows 7
    Microsoft Windows 7 x64
    Microsoft Windows 2008 R2
    Microsoft Windows 2008 R2 x64

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Well, I wasn't confident it was for my board..

www.g-sun.no/en/

G-Sun's Website

  • G-Sun
  • ADAT user
  • Offline
  • Registered: 2010-05-13
  • Posts: 29

Re: hdsp 9632 -not able to use latency under 512 for vsti

Had the same issue again, fixed with hot boot

www.g-sun.no/en/

G-Sun's Website