You are not logged in. Please login or register.
RME User Forum → HDSP(e) series → Midicontrol of total mix presets
HI,
I'm trying to figure out if you can set presets of total mix with a midi controller, but i cannot find any documentation on how the midi mapping works. As far as i can tell from triggering the presets in total mix itself nothing happens, but that obviously doenst mean much because it could just be a receive and not sending midi.
Is there a pdf with the mapping, or at least how can i triggere a preset change in total mix?
Thanks
Anton
That information is in the manual, Chapter TotalMix, Simple MIDI Control.
Thanks a ton Matthias. Gonna test it out straight away.
Btw for those lookin for the same thing here's what the manual says about it:
on midi channel 1.
note in hex/dec/name
Preset 1: 36 / 54 / #F 2
Preset 2: 37 / 55 / G 2
Preset 3: 38 / 56 / #G 2
Preset 4: 39 / 57 / A 2
Preset 5: 3A / 58 / #A 2
Preset 6: 3B / 59 / B 2
Preset 7: 3C / 60 / C 3
Preset 8: 3D / 61 / #C
Unfortunatly it does not seem to be working. Ive specified the correct midi input device. And im sending the correcte note on message (note 54 & 55 to select preset 1 & 2) yet nothing happens. I've verified the midi info is coming through correctly to other applications on the right channel etc.
Interestingly i do get the faders to work correctly with cc messages. so its def. not my midi.
The manual you look into is outdated. Correct values:
Preset 1: 36 / 54 / #F 3
Preset 2: 37 / 55 / G 3
Preset 3: 38 / 56 / #G 3
Preset 4: 39 / 57 / A 3
Preset 5: 3A / 58 / #A 3
Preset 6: 3B / 59 / B 3
Preset 7: 3C / 60 / C 4
Preset 8: 3D / 61 / #C 4
Also make sure Mackie Protocol support is activated.
>>Also make sure Mackie Protocol support is activated.
Can't this be considered a "bug" or design flaw, at least?
Shouldn't the preset notes, as well as Dim etc be Mackie Protocoll independant?
I use a Pitchbend dial to fine control a Cubase EQ. It sends PB on channel 9. The same MIDI device is used as MIDI Input to TotalMix to control its Dim. Now PB 9 also controls Master Fader in TotalMix due to Mackie Protocoll enabled for Dim to work, which interferes with Cubase.
I don't want Mackie Protocol, but still switch presets and control Dim in TotalMix...
We are thinking about changing this as well.
Is totalmix (old) still developed further?
Only bugs are fixed.
Oh... So nö changes to Midi implementation anymore? Bummer
Unfortunately, I am also unable to midi select presets in TotalMix. I have tried everything, literally! I have step sequenced every CC on every channel and sent them to TotaMix in both "simple" MIDI and Mackie protocol mode and nothing! Fader control/sub mix selection works so my midi set up is fine. Any suggestions?
Full velocity for those notes.
Ok thanks for thew help, got it! My main problem is I was sending only Note ON messages, Totalmix requires the Note OFF message. Also my sequencer shows the keys an octave lower than described in the manual so I need to start at F#2 rather than F#3. Decimal index is the same, but I was mistaking the decimal column as a CC# column.
RME User Forum → HDSP(e) series → Midicontrol of total mix presets
Powered by PunBB, supported by Informer Technologies, Inc.