• Registered: 2011-04-06
  • Posts: 18

Topic: I can´t change the volume

Hi everyone,

I have been having a problem for a while now. When I turn the volume potentiometer, no matter if it is on main out or phones, the volume does not change. It makes a feint, but stays at the same volume.

The only option I have is when I press vol and it is on the linked screen, then, if I press encoder 1 and turn that wheel, then I can change the main out volume and the same happens with the phones volume if I use encoder 2, but I can't regulate the volume as before, just using the volume potentiometer.

Any suggestions?
Thanks in advance

  • ramses
  • DAW Mastermind
  • Online
  • From: UTC+1
  • Registered: 2012-10-14
  • Posts: 13,183

Re: I can´t change the volume

Check manual, "lock volume".

BR Ramses - UFX III, 12Mic, XTC, ADI-2 Pro FS R BE, RayDAT, X10SRi-F, E5-1680v4, Win10Pro22H2, Cub14
  • Registered: 2011-04-06
  • Posts: 18

Re: I can´t change the volume

Lock volume in both is "off"

  • From: Germany
  • Registered: 2007-04-10
  • Posts: 9,770

Re: I can´t change the volume

Which device is this? Does the display show a volume change?

Regards
Daniel Fuchs
RME

RME Support's Website

  • Registered: 2011-04-06
  • Posts: 18

Re: I can´t change the volume

ADI-2 Pro FS
when I try to change the volume, the numbers blink as if they are going to change, but return to the same value. The same thing happens if I try to change the panning.

  • Registered: 2011-04-06
  • Posts: 18

Re: I can´t change the volume

It's like it's all in lock, but it's not.
The firmware is at the latest version.

  • From: Germany
  • Registered: 2007-04-10
  • Posts: 9,770

Re: I can´t change the volume

delpinator wrote:

Lock volume in both is "off"

Tried toggling the setting on and off again?

Regards
Daniel Fuchs
RME

RME Support's Website

  • Registered: 2011-04-06
  • Posts: 18

Re: I can´t change the volume

Yes, I have tried it.
In lock, the values do not flicker and remain fixed.

  • From: Germany
  • Registered: 2007-04-10
  • Posts: 9,770

Re: I can´t change the volume

Does this happen with and without connection to a computer? Is the firmware up to date?

Regards
Daniel Fuchs
RME

RME Support's Website

  • Registered: 2011-04-06
  • Posts: 18

Re: I can´t change the volume

Yes, this happens connected via USB or not connected.
As I said before, it is fully up to date.
It is something very strange, since this has happened from one day to the next one, without any reason or changes.

11 Reply by KaiS (edited by KaiS 2023-10-19 09:33:51)

  • KaiS
  • DAW Mastermind
  • Offline
  • From: Germany
  • Registered: 2020-02-05
  • Posts: 3,525

Re: I can´t change the volume

Try a reset:

While powering up, push and hold the VOL button (NOT the VOLUME dial) and Encoder 1, until you see the message: “Reset done“.

User Setups and EQ Presets are not deleted.


Or a full factory reset:

While powering up, push and hold the VOL button (NOT the VOLUME dial) and Encoder 1 and Encoder 2, until you see the message: “Reset done“.

All user Setups and EQ Presets are deleted.
Take notes before, or store them through the Remote App, if you want to keep some.

KaiS's Website

  • ra990
  • New member
  • Offline
  • Registered: 2023-05-26
  • Posts: 4

Re: I can´t change the volume

Are you playing back DSD by any chance with direct DSD option? I believe volume control is disabled in this case.