Matthias, thank you very much, that's really great.

Furthermore, cleverly done in terms of implementation, simply divided into groups of 4 to be able to operate a 4, 8 and 12 mic port scheme.

Had only time for short tests. From what I can see, works solid for Octamic XTC and 12Mic on a MADI bus (UFX III).

Even with mouse wheel settings to scroll 5 lines at once it is possible to smoothly operate the gain.

Excellent!

I wrote in the 1.96 Beta thread reporting a small issue regarding fader groups not being saved under certain conditions and I've just discovered now in 1.97 b1 a bit more about the issue.

I'm trying to save 2 different output faders into a Fader group - one stereo main out and one mono LFE output. Use case here is trying to sync a subwoofer fader to be part of main volume out in a 2.1 setup.

I have a workspace where one snapshot is 2.0 and another snapshot is 2.1. If I save the workspace when the 2.1 snapshot is selected and fader group on as described, and later reload this workspace, the Fader group with Main Out + LFE out is still grouped as expected. If I then select any other snapshot and come back to my 2.1 snapshot the LFE channel is not remembered in the group I made.

Also if I save the workspace with anything other than the 2.1 snapshot selected and reload the workspace and then select the 2.1 snapshot the LFE fader is also left out of the group.

Hopefully this makes sense so it can be logged.

For me it's the opposite.
Changes in web and Connector are shown in TM but changes in TM do nothing at all.

It's all looking good in TM when I route 1610 Pro to MADI 1-16 and 12 Mic to MADI 17-28

- Working only one way: either MIDI In or Out port are assigned wrong or not connected to the external unit

- General setup: the dialog follows a simpe rule -  the most top entry, selecting the channel bank of the audio interface, sets all others. For example you can not change the Device ID and expect that you now see the values of Device x. What you did is that you gave the still selected channel bank (top entry) a different Device ID.

- When closing that settings dialog and reopening it the top entry defaults to the first available channels! Not noticing that you might think the settings have changed - they have not, which will be clear when you select the correct channel bank (top entry) again.

- The concept of 'Aux Devices' is based on TM FX setting (sending) all parameters on start. A readback first on start does not exist. We're thinking about an option to do so.

- Note that simultaneous usage of TM FX and Remote is not implemented - never was - and will cause random and undefined behaviour.

In Totalmix menu Options / Settings Tab General
Pull the faders fully right side
and assign to none

okay for whatever reason:
- set the input to none, dim to -65dB, hit OK

closed settings,  then went back and set it back to AN8 and 0dB and it now works as expected.

If i just went into settings and wiggled talkback around and clicked "OK" it didn't hold the settings.

Aware.
Talkback dim was set to 0dB, as i had it set before beta versions, but after installing beta, it set itself to -20dB while settings were still displaying it as 0dB. I opened settings, wiggled it around back to zero, clicked OK, but it stayed -20dB (while settings displaying 0dB)

(Then i don't remember if i set it to -whatever and OK'd it or not)
Only then have I changed it to NONE, -65dB, OK'd it, and set it back to 0dB and AN8 and now it works as it used to.

Hello, how can I assign the 12 mic entries of my 12mic in Totalmix, I succeed for the first 8, but not for the last 4.

I'm using an UFX+ and a 12mic.

thanks

How can I access to the 2nd screen with Madi 9-16 if it's already used with Madi 1-8 ?
Do I need to run a 2nd totalmix window ?

I'm maybe stupid but if the channel bank is already used for MADI 1-8, hopw can, I add Madi 9-16 to use the 12 mic entries  ?

Maybe take a closer look? ;-)
You've used the drop-down menu before ... When selecting the device type, you can see for which port ranges you are selecting. As it is difficult to make 12 ports from a range of 8 ports, half of the ports from the next block of 8 are used for the last 4 ports. Take some time and look again at the two screenshots and the penny will drop.

> ok, I'm stupid ....

Don't worry, such things happen to us all :-)

If you use MADI coax then you need a different MIDI port, UFX+ Midi Port 4 (manual ch 21.4).

Fon input and output?

Is this the only device which is connected to MADI?

If yes, do you have a MADI connection from UFX+ to 12Mic and back to UFX+?

UFX+-----MADI------->12Mic
  ^                               |
   |                               |
   +---------<-------------+

If you have connected more than one device in a serial fashion (one after the other) then all devices need to be turned on, so that MADI signals are passed through to the next device in the chain and finally back to the UFX+.

UFX+-----MADI------->12Mic--------MADI----->NextMADIDevice
  ^                                                                           |
   |                                                                           |
   +---------<------------------------------------------------+

I tried here several things for you, as it was also interesting for me, it turned out that

- Auxdevice still works if UFX III MADI frame is set to 96k and if you choose 48k on the 12Mic
  Nevertheless, I would recommend you to choose the same MADI frame size on all devices, best 96k

- Auxdevice still works if you do not not pass through all MADI channels, which are not in use by the 12Mic.
  But should you should chain several MADI devices on the one MADI bus of the UFX+ in the future, then
  you need to configure the routing not only for the 12Mic itself.
  You also need to configure to pass through all other channels
  E.g.
  Mic In 1..12 -----> MADI 1-12
  MADI 13-64 -----> MADI 13-64 (pass through of the other MADI channels)

I have only one device connected to my UFX+, madi out to madi in and madi in to madi out

sorry, no idea.

Yep, thanks.

could I send you some screenshot of my config ?

If vertical size changes were possible why do we need the Zoom fixed steps then?

Vertical is NOT possible and never was.

Hello

First of all congratulations for this 'Modern Art Piece' in software form called TotalMix, IMHO (probably) the best GUI mixer and a demonstration of respect for us Users/Customers. I'm NOT suck up to RME, that's what i think.

As a self-recording musician my UCX II and TM offers me much more than needed but please, I would love enjoy some features coming from Stand-Alone operation in next TM FX 1.97 RC (Release Candidate) or future versions. These are my requests:

• Add option to load the 6 UCX II physical memory Setups into TM, not just save.

• Add option in TM Preferences to enable/disable the dialog warning forcing to choose [Device] or [TotalMix] coming from Stand-Alone and load directly the last Setup used on UCX II before online.

Thanks for read

I would also like, if it would be possible to load setting's slots 1-6 from device to TM.

I know, one may load a slot to HW and also store it in computer for referencing.... But one may use many computers. And one often is not perfect in archiving and so on. So, being able to load what is stored in HW would be IMHO beneficial. One could check beforehand that the routing stored is the right one.

ad 2) IMHO OP wants the opposite... TM loads routing last used from interface without asking.

Setups stored in the unit (for stand-alone mode) miss the complete software playback part of the mixer, for obvious reasons. That's why there will be no import into TM FX.

The current total state is just a (one) state, and not a memory slot. For storing that one  1 or 6 times there is no memory.